Idaho Admin. Code r. 24.39.80.301 - FALLING AND BUCKING
01.
General
Requirements. (3-31-22)
a. There shall
be an established method of checking-in workers from the woods. Each supervisor
shall be responsible for their crew being accounted for at the end of each
shift. (3-31-22)
b. Cutters not in
sight of another employee shall have radio communications with crew members on
that job site. (3-31-22)
c. Common
sense and good judgment must govern the safety of cutters as effected by
weather conditions. At no time shall they work if wind is strong enough to
prevent the falling of trees in the desired direction, or when vision is
impaired by weather conditions or darkness. (3-31-22)
d. All cutters shall have a current first aid
certification. Employers shall provide an opportunity for cutters to take a
standard first aid course. (3-31-22)
e. Tools of cutters such as axes, sledges,
wedges, saws, etc., must be maintained in safe condition. Battered sledges, and
wedges shall not be used. When power saws are used, wedges shall be made of
soft material, such as wood or plastic. (3-31-22)
f. Cutters shall not be placed on hillsides
immediately below each other or below other operations where there is possible
danger. (3-31-22)
g. Trees shall
not be felled if a falling tree endangers any worker, line, or any unit in
operation. (3-31-22)
h. Before
starting to fall or buck any tree or snag, the cutter must survey the area for
possible hazards and proceed according to safe practices. Snags, which are
unsafe to cut, shall be blown down with explosives, or felled by other methods.
(3-31-22)
i. Dangerous or hazardous
snags shall be felled prior to or in the course of cutting a strip. No danger
tree shall be felled by one (1) cutter where and when the assistance of a
fellow employee is necessary to minimize the danger or hazards involved. In the
case that any danger tree or snag cannot be safely felled and must remain
standing or unattended, such tree or snag shall be clearly identified and
suitably marked, including all surrounding impact area, and the employee's
supervisor shall be notified as soon as possible. (3-31-22)
j. In falling timber, adjacent brush and snow
shall be cleared away from and around the tree to be felled to provide
sufficient room to use saws and axes and provide an adequate escape path.
(3-31-22)
k. Cutters shall not fall
into another strip; leaners on the line shall be traded. Trees shall be felled
into the open whenever conditions permit. (3-31-22)
l. Undercuts and side cuts shall be large
enough to safely guide the trees and eliminate the possibility of splitting and
barber chairing. Particular care shall be taken to hold enough wood to prevent
the tree from prematurely slipping or twisting from the stump. Undercuts shall
be cleaned out to the full depth of the saw cut. Especially large undercuts are
necessary in heavy leaners. When required to safely fell a tree, mechanical or
other means shall be employed to accomplish this objective. Pre-cutting of
trees for the purpose of production logging is prohibited.
NOTE: Trees with no perceptible lean having an undercut to a depth of one quarter (1/4) of the diameter of the tree with an undercut height equal to one fifth (1/5) of the diameter of the tree will be assumed to be in reasonable compliance with this rule. (3-31-22)
m. Back-cuts shall be above the level of the
upper horizontal cut of the undercut. (3-31-22)
n. While wedging, fallers shall watch for
limbs or other material which might be jarred loose. Cutting of holding wood in
lieu of using wedges is prohibited. (3-31-22)
o. When falling or bucking a tree is
completed the power saw motor should be stopped. The power saw motor shall be
stopped while the operator is traveling to the next tree. (3-31-22)
p. Cutters shall not work on the downhill
side of the log being bucked unless absolutely unavoidable and only when the
log is blocked or otherwise secured to prevent rolling when cut is completed.
(3-31-22)
q. Cutters must give
timely warning to all persons within range of any log which may have a tendency
to roll or slide after being cut off. (3-31-22)
r. Logs shall be completely bucked-through
whenever possible. If it becomes hazardous to complete a cut, then the log
shall be marked and identified by a predetermined method. Rigging crews shall
be instructed to recognize such marks and when possible cutters shall warn
rigging crew of locations where such unfinished cuts remain.
(3-31-22)
s. A competent person
properly experienced in this type of work shall be placed in charge of falling
and bucking operations. Inexperienced workers shall not be allowed to fall
timber or buck logs unless under the direction of experienced workers.
(3-31-22)
t. Power saws shall be
kept in good repair at all times. All exhaust parts on power chain saws shall
be constructed and maintained so the operator is exposed to a minimum amount of
fumes and noise. (3-31-22)
u.
Combustion engine driven power saws shall be equipped with an automatic
throttle which will return the motor to idling speed upon release of the
throttle. (3-31-22)
v. Power saw
motors shall be stopped while being fueled. (3-31-22)
w. All personnel shall wear approved head
protection, proper clothing and footwear. (3-31-22)
x. Each employee who operates a chain saw
shall wear leg protection, which meets the requirements of ASTM F 1897 and
covers the full length of the thigh to the top of the boot on each leg, except
when working as a climber. (3-31-22)
Notes
State regulations are updated quarterly; we currently have two versions available. Below is a comparison between our most recent version and the prior quarterly release. More comparison features will be added as we have more versions to compare.
No prior version found.