020-26 Wyo. Code R. §§ 26-11 - Plugging and Abandonment
(a) All wells that
are no longer useful (including test wells) must be plugged in order to ensure
that groundwater supply is protected and preserved for further use and to
eliminate the potential physical hazard. A well is considered "abandoned" when
it has not been used for a period of one year, unless the owner demonstrates
their intention to use the well again by properly maintaining the well in such
a way that:
(i) The well has no defects that
will allow the impairment of quality of water in the well or in the water
bearing formations penetrated.
(ii)
The well is covered and the cover is watertight.
(iii) The well is marked so that it can be
clearly seen.
(iv) The area
surrounding the well is kept clear of brush or debris.
Observation or test wells used in the investigation or management of usable sources of groundwater by state agencies or by engineering or research organizations are not considered "abandoned" so long as they are maintained for this purpose. These wells shall be covered with an appropriate cap, and labeled for their particular use.
(b) Preliminary work. Before a well is
plugged and abandoned, it shall be investigated by the permittee (owner/
operator) to determine its condition, details of construction and whether there
are obstructions that will interfere with the process of filling and
sealing.
(c) Filling and sealing.
Following are requirements to be observed when plugging wells:
(i) Wells wholly situated in unconsolidated
material in an unconfined groundwater zone shall have the uppermost thirty (30)
feet sealed with impervious material. The remainder of the well shall be filled
with clay, sand, or other suitable inorganic matters as described in paragraph
e.
(ii) Wells penetrating several
aquifers or formations containing usable water sources shall have the uppermost
thirty (30) feet sealed with an impervious material. All screened or perforated
intervals shall be sealed to prevent vertical movement of waters from the
producing or injected formation. Impervious material shall be placed opposite
the confining formation above and below (and including) the screened or
perforated interval for a minimum of fifty (50) feet or more.
(iii) Any uncased hole below the well shoe
shall be filled with an impervious material as described in paragraph e. to a
depth of at least fifty (50) feet above the shoe.
(iv) Whenever production casing has been
severed or inadvertently removed the well bore shall be filled with impervious
material from a point fifty (50) feet below to a point 50 feet above the point
of severance or to the surface limit.
(v) Wells penetrating creviced or fractured
rock shall have the portions of the well opposite this formation sealed with
neat cement, sand cement grout or concrete. If these formations extend to
considerable depth, alternate layers of coarse stone and cement grout or
concrete may be used to fill the well.
(vi) Wells in nonfractured, consolidated
formations shall have the uppermost thirty (30) feet filled with impervious
material and the non-creviced, consolidated formation portion of the well may
be filled with clay or other suitable material.
(d) Placement of material. The following
requirements shall be observed in placing fill or sealing a plugged or
abandoned well.
(i) No material shall be
placed in the well unless the Administrator has been notified that plugging and
abandonment operations are to commence. A minimum of thirty (30) days notice
must be given.
(ii) The well shall
be filled with the appropriate material as described in paragraph e. from the
bottom of the well up.
(iii)
Sealing materials shall be placed in the interval or intervals to be sealed by
methods that prevent free fall, dilution and/or separation of aggregates from
cementing materials.
(iv) When the
underground pressure head producing flow is such that a counterpressure must be
applied to force a sealing material into the annular space, this
counterpressure shall be maintained for the length of time required for the
cementing mixture to set as specified in Section
6, paragraph (c) (viii) of this
part.
(v) To ensure that the well
is filled and there has been no bridging of the material, verification shall be
provided that the volume of material placed in the well installation at least
equals the volume of the empty hole.
(e) Material. Requirements for sealing and
fill materials are as follows.
(i) Impervious
sealing materials. Sealing materials shall have a permeability of 10 - 7 cm/sec
or less. Impervious materials include neat cement, sand-cement grout, concrete,
and bentonite clay as described in Section
6, paragraph (c). Used drilling muds are
not acceptable.
(ii) Filler
material. Materials such as clay, silt, sand, gravel, crushed stone, native
soil, and mixtures of these materials, as well as those described in paragraph
(i) above may be used as filler material. Material containing organic matter or
used drilling muds shall not be used.
(f) Markings. The top of the plug of any
plugged and abandoned well shall show clearly, by permanent markings, whether
inscribed in the cement or on a steel plate embedded in the cement, the permit
number, well identification number and date of plugging.
(g) Reports. Within fifteen (15) days after a
well has been plugged and abandoned, the owner shall file a plugging record
with the Water Quality Division.
Notes
State regulations are updated quarterly; we currently have two versions available. Below is a comparison between our most recent version and the prior quarterly release. More comparison features will be added as we have more versions to compare.
No prior version found.