UNITED STATES v. DUDLEY.

The imports in this case were eight car loads of spruce boards and plank, planed on one side, and tongued and grooved. They varied from 1 to 3 inches in thickness, from 4 to 11 inches in width, and from 12 to 20 feet in length. Some were 'butted to exact lengths.' They were prepared for use by what is known as a 'flooring machine,' which is a combination of a simple planing machine with a matching or tonguing and grooving machine. Some of the smaller mills use separate machines for planing and matching, the combination machine seeming to be of comparatively recent origin. The boards were adaptable for flooring, ceiling, sheathing, etc.

They were assessed for duty under paragraph 181 of the tariff act of August 28, 1894, which imposed a duty of 25 per cent. ad valorem upon 'house or cabinet furniture, of wood, wholly or partly finished, manufactures of wood or of which wood is the component material of chief value, not specially provided for in this act.'

Upon the other hand, the importer insisted that they should have been admitted free of duty, under paragraph 676, which exempts 'sawed boards, plank, deals and other lumber, rough or dressed,' except certain lumber of valuable cabinet woods.

Forty-seven witnesses were examined before the board of general appraisers, 23 of whom testified that lumber which had been planed, grooved, tongued, or beaded was still 'dressed lumber,' even when finally shaped for the carpenter to ut together in roofing, flooring, ceiling, etc., and 24 testifying, in substance, that the term was only applicable to such as had been merely planed upon one or both sides, and brought to an even thickness. It was admitted by witnesses upon both sides that in ordering such articles the term 'dressed lumber' would not sufficiently describe them, and that they were usually ordered by description, or by their specific designation, as 'flooring,' etc.

Ordinarily, the fact that an article in the process of manufacture takes a new name, is indicative of a distinct manufacture, as was intimated in Tide Water Oil Co. v. U. S., 171 U. S. 210, 18 Sup. Ct. 837; but we do not think it important in this case that 'dressed lumber' is divisible into flooring, sheathing, and ceiling, since sawed lumber is none the less sawed lumber, though, in its different forms and uses, it goes under the names of 'beams,' 'rafters,' 'joists,' 'clapboards,' 'fence boards,' 'barn boards,' and the like. In other words a new manufacture is usually accompanied by a change of name, but a change of name does not always indicate a new manufacture. Where a manufactured article, such as sawed lumber, is usable for a dozen different purposes, it does not ordinarily become a new manufacture until reduced to a condition where it is used for one thing only. So long as 'dressed lumber' is in a condition for use for house and ship building purposes generally, it is still 'dressed lumber'; but if its manufacture has so far advanced that it can only be used for a definite purpose, as sashes, blinds, moldings, spars, boxes, furniture, etc., it becomes a 'manufacture of wood.' It follows that the words 'flooring, ceiling, sheathing,' do not, under this act, describe a new manufacture, but, rather, the different purposes for which sawed lumber may be used. It is much like the commercial division of lumber into 'selects, common, and culls,' which are all lumber, but of different qualities. None of these are in reality new names, but merely specifications of the more general term 'lumber.' Indeed, a manufacturer receiving an order for lumber could not possibly fill it, to the satisfaction of his customer, without knowing the purpose for which if was designed, or the quality desired.

The fact that 'dressed lumber' is ordered under the names of 'flooring,' 'ceiling,' 'sheathing,' does not indicate that it is not still 'dressed lumber,' but, rather, that it is of a quality of width specially adapted to those purposes. Had it been of a particular quality, width, and thickness, and sawn into lengths which would make it usable only for the manufacture of boxes, perhaps it might be termed a 'manufacture of wood,' for the purposes of this act. It is true that the lumber in question was in a condition to be used for flooring without further manufacture, except such reductions in length as the dimensions of the room might require; but it was also usable for ceiling, sheathing, and for similar purposes, with no further alterations. Had it so far been changed as to be serviceable for only one thing, it is possible that it might be regarded as a separate and independent manufacture, though, under the case of Tide Water Oil Co. v. U. S., 171 U. S. 210, 18 Sup. Ct. 837, this may admit of some doubt. But, while lumber planed upon one or both sides may be 'dressed lumber,' we think that when tongued and grooved it is still 'dressed lumber,' and not a new and distinct manufacture; in other words, that tonguing and grooving is an additional dressing, but it does not make it a different article. Lumber treated in this way is still known in the trade as lumber; advertised as lumber; handled as lumber; shipped as lumber; bought and sold by the thousand feet, like lumber.

We also think that some light upon the proper construction of the words 'manufacture of wood,' in paragraph 181, is afforded by the fact that it is used in connection with 'house or cabinet furniture of wood, wholly or partly finished,' and is foll wed by the words, 'or of which wood is the component material of chief value.' This would indicate an article 'made up' of wood, analogous to furniture, or other article in which wood is used alone or in connection with some other material. It seems to us quite clear that it could not have been intended to apply to lumber which had only passed beyond the stage of planed lumber by being tongued and grooved.

Upon the facts of the present case, we are of opinion that the imports in question should habe been classified as 'dressed lumber,' and the judgment of the circuit court of appeals is therefore affirmed.