700 CMR, § 7.08 - Limitations on Large Tandem Units
(2)
Use
of Ways. Tandem units are not permitted in the Tunnels. No
operator may operate a large tandem unit on any way other than the Turnpike. An
operator may operate a large tandem unit on the Turnpike only if the Department
has issued a large tandem unit permit pursuant to
700 CMR
7.07(2).
(3)
Configuration and
Length. A complete large tandem unit consists of a tractor, first
semi-trailer, dolly, and second semi-trailer. The length of either semi-trailer
may not be in excess of 48 feet, and the total length of the combination,
including the dolly and load, may not exceed 120 feet, provided, however, that
the overall length of loaded tandem trailer automobile haulers may not exceed
108 feet and may be increased to 109 feet by load overhang.
(4)
Maximum Gross
Weight. A large tandem unit must be registered for the gross
weight that it carries and certified by the original manufacturer to carry this
weight. The vehicle weight of a large tandem unit may not exceed 127,400
pounds. The maximum gross weight of the tractor and first semi-trailer may not
exceed 71,000 pounds. The maximum gross weight of each unit of dolly and
semi-trailer may not exceed 56,400 pounds.
The maximum gross weight that may be carried upon any combination of units is limited by the maximum gross weight that can be carried upon each unit and its axles. The maximum gross weight for the unit of tractor and first semi-trailer is governed by this formula: 35,000 pounds plus 1,000 pounds per foot between the center of the foremost axle of the tractor and the center of the rearmost axle of the first semi-trailer. The gross load on a unit may not exceed the sum of the allowable gross loads on the axles, which are as follows:
|
Maximum gross weight on any one axle |
22,400 pounds |
|
Tandem axles on one vehicle (under ten feet apart) (Axles measuring less than 46 inches between axle centers are considered as one axle.) |
36,000 pounds |
The limit of 127,400 pounds permitted under 700 CMR 7.08(4) requires a minimum axle spacing of 92 feet, measured betwee n the center of the foremost axle of the tractor and the center of the rearmost axle of the rearmost semi-trailer. If the axle spacing is less, the permissible gross weight is correspondingly reduced.
(5)
Size and Weight Limitations
Generally. The provisions of
700 CMR 7.00 with respect to
size and weight that are not inconsistent with 700 CMR 7.08(4) are applicable
to large tandem units unless specifically excluded under the terms of a large
tandem unit permit.
(6)
Approval of Vehicle or Equipment Used to Tow. The
owner or lessee of a large tandem unit must file a description of the tractor,
dollies, and any semi-trailer used to tow another semi-trailer with the
Department on Forms MTT-3, MTT-4, and MTT-5, respectively. The owner or lessee
must obtain the Department's approval of the vehicles before they are used
under a large tandem unit permit. The Department may withdraw its authorization
to use the vehicles at any time at its sole discretion.
(7)
Certification of
Tractors. No operator may operate a large tandem unit unless the
Department has certified that the tractor of the unit is appropriate for the
purpose. Both the tractor manufacturer of each tractor used in a large tandem
unit and the owner or lessee of the unit must certify to the Department prior
to the approval of the tractor that it is capable of hauling the maximum
permissible gross load to be transported by the owner or lessee at a speed not
less than 20 m.p.h. over the Turnpike. (The maximum grade on the Turnpike is
7.50%, and the length of the longest such grade is approximately 1.75 miles.)
If it is determined after the tractor is in use as part of a large tandem unit
that the tractor cannot meet this requirement, the Department's approval may be
withdrawn, and, in that event, the tractor may not be used as part of a large
tandem unit on the Turnpike until the gross loads are reduced, the tractor is
modified, or other corrective measures are taken. Upon a new certification by
both the tractor manufacturer and the owner or lessee that corrective measures
have been taken and the tractor is now capable of complying with the minimum
speed requirement, the Department may reinstate its approval of the
tractor.
(8)
Certification of Trailers. No operator may operate a
large tandem unit unless the Department has certified that the trailer of the
unit is appropriate for the purpose. In order to comply with 700 CMR 7.08(13),
all semi-trailers, except the rear trailer used in tandem operation, must have
sufficient structural strength to permit the satisfactory attachment of the
coupling device (pintle hook or its equivalent) at the rear of the trailer, and
each coupling device must be capable of towing a trailer and a dolly. The
permittee shall certify to the Department that every trailer certified for use
in tandem service is adequate for this service and, in addition, the trailer
manufacturer on new equipment must certify the adequacy of the trailer. If the
trailer has been modified to include a pintle hook, the fabricator must certify
the adequacy of the pintle hook assembly. Every coupling dev ice must
incorporate a no-slack design such as air take-up, fitted pin and socket,
mechanical wedging, or similar coupler designs, that eliminate fore and aft
slack in the coupling of dollies to semi-trailers. The no-slack feature of the
coupler must be in constant operation while the tandem trailer combination is
operated on the Turnpike. The coupler used on each semi-trailer, in conformance
with 700 CMR 7.08(8), must be specified by the permittee on Form MTT-4, giving
semi-trailer descriptions and the vehicle identification number on the
permittee's records (company number) and must be filed with the Department in
conformance with 700 CMR 7.08(6).
(9)
Brakes.
(a)
Compliance with Federal
Regulations. The brakes on a vehicle or dolly converter or
combination of vehicles used in a large tandem unit must comply with federal
regulations as published in 49 CFR Part 393 , Subpart C, as revised and
effective on the date of the vehicle's entry upon or use of the
Turnpike.
(b)
Compliance with State Law. A vehicle or dolly
converter or combination of vehicles used in a large tandem unit must meet the
requirements of the provisions of the M.G.L. c. 90.
(c)
Braking Devices
Required. The brake application line of every large tandem unit
certified on or after June 1, 1968, must be equipped with suitable devices to
accelerate application and release of the brakes of the towed vehicles. These
devices must be so arranged that the brake application signal does not pass
directly through more than one trailer, but is dead-ended at the rear of the
trailer or, alternatively, at the dolly, and the application signal then is
retransmitted to the dolly and the second trailer. The devices required for
retransmission of the application signal must be closely connected to and
supplied by air reservoirs that have their air supplied to them by the
emergency line. In the event of rupture of the application line on the towed
vehicle of a large tandem unit, the loss of brake application must be limited
upstream of the loss to those vehicles between the rupture and the first
retransmission device.
(d)
Brakes on Steering Axle. A tractor used in a large
tandem unit must have brakes on the steering axle.
(10)
Axles. A
tractor used in a large tandem unit with a gross weight of more than 110,000
pounds must be equipped with tandem rear axles, each of which must be engaged
to bear its full share of the load on the roadway surface.
(11)
Emergency
Equipment. Each tractor used in a large tandem unit must be
equipped at a minimum as follows:
(b)
Fuses. At least one spare fuse or other overload
protective device, if the devices used are not of a reset type, for each kind
and size used.
(c)
Chains. One set of tire chains for at least one
driving wheel on each side between October 15th and
May 1st.
(d)
Fire
Extinguishers. Fire extinguishers that have an aggregate rating of
20 BC.
(12)
Vehicle Identification. The owner or lessee shall
stencil the tractor weight on the left side of each tractor used in a large
tandem unit. The Department issues an identification number that the owner or
lessee shall also stencil on the left side of each tractor used in a large
tandem unit. The Department also issues a certificate bearing the complete
description of a particular tractor, including the maximum permissible gross
load to be transported, and the operator shall suitably protect and carry this
certificate in the cab of the tractor that it describes. A vehicle certified
for less than 127,400 pounds may not exceed the weight indicated on the
certificate. The Massachusetts State Police and Department personnel may
examine the certificate and compare its description with the vehicle in which
the certificate is carried. A discrepancy between the description on the
certificate and the actual description of the vehicle may result in the
withdrawal of the approval of the particular tractor or all of the vehicles and
equipment of the owner or lessee. Compliance with the Provisions Governing the
Operation of Tandem Trailer Combinations of the New York State Thruway
Department requiring the issuance of an identification number, its stenciling
on the tractor, and the issuance of a certificate describing the tractor is
compliance with the similar requirements of 700 CMR 7.08.
(13)
Tandem
Assembly. In the assembly of large tandem units prior to their
operation on the Turnpike, the operator shall ascertain the total gross weight
of each trailer of the proposed combination. In the event that the gross
weights of the trailers vary by more than 20%, the operator shall couple them
for each trip according to their gross weight, that is, with the heaviest
trailer coupled to the tractor.
(14)
Dollies, Safety Chains, and
Cables.
(a)
Converter
Dolly. Every converter dolly certified on or after June 1, 1968,
used to convert a semi-trailer to a full trailer may have either single or
tandem axles. The operator shall couple the dolly with one or more safety
chains or cables to the frame, or to an extension of the frame, of the motor
vehicle by which it is towed. Attachment of these chains or cables to the
pintle hook or to any other device on the towing vehicle to which the tow bar
is attached does not meet this requirement; provided, however, that a separate
place of attachment independent of the pintle hook on a pintle hook forging or
casting may be used to attach the safety chains or cables to the towing
vehicle.
(b)
Slack in
Chains or Cable. Safety chains or cables may have no more slack
than is necessary to permit proper turning.
(c)
Strength of Chain or
Cable. Each chain or cable and each means of attachment must have
an ultimate strength at least equal to the gross weight of the vehicle being
towed.
(d)
Connection
of Chain or Cable. Chains or cables must be connected to the towed
and towing vehicles and to the tow bar in a manner that prevents the tow bar
from dropping to the ground in the event that the bar fails or becomes
disconnected.
(e)
Chain
or Cable on Converter Dolly with Hinged Tow Bar. Every converter
dolly with a hinged tow bar must be equipped with two safety chains, or cables,
or a bridle arrangement of a single chain or cable, attached to its frame or
axle at two points as far apart as the configuration of the frame or axle
permits. These chains or cables must be either two separate pieces, each
equipped with a hook or other means for attachment to the towing vehicle, or a
single piece leading along each side of the tow bar from the two points of
attachment on the towed vehicle and arranged into a bridle with a single means
of attachment to be connected to the towing vehicle. When a single length of
cable is used, a thimble and twinbase cable clamps must be used to form the
forward bridle eye. The hook or other means of attachment to the towing vehicle
must be secured to the chain or cables in a fixed position.
(f)
Chain or Cable on Converter
Dolly without Hinged Tow Bar. Converter dollies with solid tongues
and without hinged tow bars or other swivels between the fifth wheel mounting
and the attachment joint of the tongue eye or other hitch device may be
equipped with either one or two safety chains or cables, provided that, if only
one chain or cable is used, it must be in line with the center line of the
trailer tongue. The point of attachment of these chains or cables to a solid
tongue converter dolly is optional provided only that the attachment is to the
rear of the attachment of the tongue eye or other hitch device.
(g)
Points of
Attachment. Where two safety chains or cables are used and
attached to the towing vehicle at separate points, the points of attachment on
the towing vehicle must be located equally distant from, and on opposite sides
of, the center line of the towing vehicle. Where two chains or cables are
attached to the same point on the towing vehicle, and where a bridle or a
single chain or cable is used, the point of attachment must be on the center
line of the towing vehicle.
(h)
Compliance with Federal Regulations. Coupling devices
and towing devices must comply with the federal regulations as stated in 49 CFR
Part 393, Subpart F, on the date of the large tandem unit or one of its
component's entry upon or use of the Turnpike.
(15)
Indication That Trailers
Form One Unit. When the distance between the rear of the one
semi-trailer and the front of the following semi-trailer is ten feet or more,
the dolly must be equipped with a device, or the trailers must be connected
along the sides with suitable material, that will indicate to other traffic
that the trailers are connected and are operating as one unit. The Department
must approve the type of device or connection prior to its use on a large
tandem unit.
(16)
Lighting. Each trailer in a tandem trailer combination
must be equipped at a minimum with electric lamps and reflectors mounted on the
vehicle as follows:
(a)
Amber
Clearance Lamps. Two amber clearance lamps on the front, one at
each side of the trailer.
(b)
Rear Lamps. On the rear: one red tail lamp; one red or
amber stop lamp; two red clearance lamps, one on each side; two red reflectors,
one on each side.
(c)
Side Lamps. On each side: one amber side-marker lamp
located at or near the front; one red side-marker lamp located at or near the
rear, one amber reflector, located at or near the front; one red reflector,
located at or near the rear.
(d)
On Dolly Converter. Each dolly converter, when towed
singly by another vehicle, and not as a part of a full Trailer, must be
equipped with a minimum of one stop lamp, one tail lamp, and two reflectors on
the rear.
(17)
Equipment Inspection. The operator of a large tandem
unit is responsible for ensuring that all certified tandem trailer equipment is
systematically inspected and maintained by a competent mechanic and kept in
first class condition. Inspection and maintenance of the equipment must be in
accordance with the requirements outlined in 49 CFR 396.
After all of the component vehicles in a large tandem unit are completely hooked up, and prior to the departure of the large tandem unit from the assembly area, the operator, or a mechanic, shall, in addition to the pre-trip equipment inspection and use requirements set forth in 49 CFR 392.7 and 49 CFR 392.8, inspect the large tandem unit and make certain tests on the vehicle, equipment, and hook-up to determine whether each item is in safe and proper operating condition.
The items to be inspected and tests to be made include, but are not to be limited to, the following:
-Federal equipment inspection.
-Inspection of brake line to dolly and trailers.
-Inspection of electric lines to dolly and trailers.
-Inspection of coupling devices.
Following this inspection and prior to departure from the assembly area, the operator shall complete and execute a tandem trailer inspection report form provided by the Department. A new inspection report must be prepared each time the component parts of the tandem trailer unit are rearranged, or the operator is replaced, or upon re-entry to the Turnpike after any valid departure. The operator shall keep an original inspection report in an accessible place in the vehicle for which it was prepared, and this original inspection report must be presented to an official or employee of the Department, or a Massachusetts State Police officer on demand.
(18)
Registration of
Operators. Proposed operators of large tandem units must be
registered with the Department prior to operating such equipment on the
Turnpike. Completed applications for registration must provide all specified
driving, safety, and physical examination records and be accompanied by an
official abstract of the driving record of the individual for whom it is being
submitted. An applicant for registration as an operator of a large tandem unit
must demonstrate to the Department that the applicant has a minimum of five
years of tractor trailer driving experience. The Department issues a special
identification card to each registered operator of a large tandem unit, and
each registered operator shall carry this card and display it upon request to a
Massachusetts State Police officer or Department personnel. A registered
operator may hold a large tandem unit permit for two companies at the same
time, provided that each company has filed an application for this permit with
the Department and that the Department has approved this permit. The special
identification card is valid only for the operation of tractors owned or leased
by the company by whom the operator is employed. The Department may decline to
register an applicant or cancel a registration at any time should the
Department determine that operational or safety considerations warrant its
doing so. An operator's qualification for and possession of a valid special
identification card of the New York State Thruway Department satisfies the
requirements of 700 CMR 7.08.
(19)
Speed Regulations. The operator of a large tandem unit
shall strictly comply with the speed regulations for these units. In
particular, an operator of a large tandem unit shall strictly observe the 55
m.p.h. speed limit as well as any lower posted speed limit.
(20)
Distance Between
Vehicles. The operator of a large tandem unit shall maintain a
minimum distance of 500 feet, or approximately two delineator spaces, under
normal conditions between a large tandem unit and a vehicle traveling in front
of it in the same travel lane, except when passing occurs.
(21)
Insurance. In
order to comply with the Department's insurance requirements for large tandem
units, the permittee must supply the Department with either a duplicate copy of
its automobile liability insurance policy or a certificate of insurance
evidencing automobile liability coverage. The policy or certificate of
insurance must include the insurance requirements found in the large tandem
unit permit application or other applicable form or document provided by the
Department.
(22)
Passing. A large tandem unit may pass another vehicle
traveling in the same direction only if the speed differential between the
large tandem unit and the vehicle that the large tandem unit is overtaking is
adequate to allow the large tandem unit to complete the passing maneuver and
return to the unit's driving lane within a distance of one mile.
(23)
Reports and
Observation. The owner or lessee shall, upon request, furnish to
the Department all data and information pertaining to an individual trip by a
large tandem unit or the overall large tandem unit operations of the owner or
lessee on the Turnpike. The owner or lessee shall afford representatives of the
Department the opportunity to observe the large tandem unit operations on the
Turnpike by riding in the cab of the tractor or using other prescribed methods,
all in accord with governmental regulations and insurance
requirements.
(24)
Payment of Fees and Tolls. An applicant must pay the
fees that are specified in the permit application and in
700 CMR
7.07(3): Table
5, and the toll charge. The toll for a large tandem unit is the toll
charge based on the classification of the vehicle under
700 CMR
7.03(1).
(25)
Emergency Service and Towing
Vehicles. An emergency service or towing vehicle that an owner or
lessee uses to maintain its large tandem units may be certified for operation
on the Turnpike on Form MTT-1, provided that the owner or lessee certifies on
Form MTT-1 that:
(a) The emergency service or
towing vehicle is completely equipped with emergency lighting
equipment.
(b) The use of the
emergency service or towing vehicle will conform to the provisions of
700 CMR 7.00.
(26)
Renewal of
Permits. The Department may renew a large tandem unit permit
monthly or annually upon the owner's or lessee's submission of Form MTT-2
requesting renewal. Form MTT-2 must be accompanied by a letter, on company
stationery, signed by a duly authorized designee of the owner or lessee
requesting recertification of the equipment to be continued in use in the
operation of the large tandem unit, which has been certified previously
pursuant to 700 CMR 7.08(8). The letter must be substantially similar to and
include the information set forth in the sample letter that the Department
supplies entitled "Sample Letter for Recertification of Tandem Equipment".
According to the following schedule, the Department may subject an owner or
lessee of a large tandem unit to a probationary period or to a period of
suspension of operations based on the owner's or lessee's cumulative violations
of motor vehicle laws or regulations or
700 CMR 7.00 that occur within
a permit's annual renewal period:
(a) three
violations - six month renewal
(b)
six violations - three month renewal
(c) nine violations - one month
renewal
(d) 12 violations -
suspension of large tandem unit permit
(27)
Limitations on
Permits. The Department may, at its sole discretion, and, in whole
or in part, revoke or temporarily suspend at will a large tandem unit permit.
The Department's issuance of a large tandem permit creates no property
interest, and the Department retains the right to amend or repeal, in the
Department's sole discretion and the exercise of its police or other powers,
the provisions of 700 CMR 7.08 pursuant to which large tandem unit permits are
issued. The Department may temporarily suspend large tandem unit operations at
any time and for any reason. Should the Department temporarily suspend
operations of large tandem units, for example, because of inclement weather,
reconstruction, or other adverse operating conditions, an operator of a large
tandem unit shall comply with the instructions of the Department or the
Massachusetts State Police immediately or as promptly as safe operating
practices permit.
(28)
Makeup-breakup Areas. Tandem trailer units may be
assembled and disassembled only in special makeup-breakup areas that the
Department designates for this purpose. No combination consisting of a tractor,
first semi-trailer and dolly, with or without a second semi-trailer, may leave
the Turnpike and pass on to a public highway or road within the Commonwealth of
Massachusetts unless permitted by law. The owner or lessee of a vehicle
entering or leaving a makeup-breakup area shall supervise the movement of the
vehicle across traffic to minimize the possibility of accidents. The owner or
lessee of a tandem trailer unit shall employ appropriate and adequate
protection devices, such as flags, flares, or lights, to warn and stop traffic
while the vehicles are maneuvering. The owner or lessee of a tandem trailer
unit is solely responsible for its vehicles and equipment, as well as their
contents, while the vehicles and equipment are in a makeup-breakup area. Large
tandem units or components of them, except dollies, may not be parked in
makeup-breakup areas for more than eight hours. The use of makeup-breakup areas
is restricted to trailers of registered owners or lessors that exceed 28 feet.
A tandem trailer unit left in a makeup-breakup areas must be disassembled while
parked in tandem lots. A trailer parked in a makeup-breakup area containing
hazardous materials must have its cargo's shipping papers available in an
accessible place on the front of the trailer for inspection by the Department
or a Massachusetts State Police officer.
(29)
Penalties.
Whoever violates any provision of 700 CMR 7.08 shall be punished by a fine not
exceeding $500 for every such offense.
Notes
State regulations are updated quarterly; we currently have two versions available. Below is a comparison between our most recent version and the prior quarterly release. More comparison features will be added as we have more versions to compare.
No prior version found.